Differences

This shows you the differences between two versions of the page.

--- project:maerklin:warnemuende:lighthouse:start [2025/06/11 14:50] – [Design] Peter Siegmund
+++ project:maerklin:warnemuende:lighthouse:start [2025/09/23 07:34] (current) – [KiCad] Peter Siegmund
@@ Line 1: / Line 1: @@
 ====== Mole Beacon ======
-===== Introduction =====
 {{ :project:maerklin:warnemuende:lighthouse:mole_beacon_light.png?200|}}
+===== Introduction =====
 For our Warnemünde section, which includes a water area, we also need a lighthouse so that our ships can travel safely.
@@ Line 9: / Line 9: @@
 Since Warnemünde has two [[https://de.wikipedia.org/wiki/Molenfeuer_Warnem%C3%BCnde|Mole Beacons]] (one green and one red), I decided to recreate the green beacon light. I did some research and found some good reference images for this project.
+===== Source Code =====
+Everything can be found in the [[https://git.mars3142.dev/model-railway/warnemuende-lighthouses|git repository]].
+This device will have three services: **0x180A** (device information services), **0xA000** (light service) and **0xA999** (settings service). Within the services will be specific characteristics, but I don't will describe it here in detail.
+If you need more information about the BLE communication visit the [[..:..:system_control:ble:start|]] page.
 ===== Design =====
-{{:project:maerklin:warnemuende:lighthouse:testprint_01.jpeg?200 |}}
+{{:project:maerklin:warnemuende:lighthouse:mole_beacon_light_cut_through.png?200 |}}
 First, I replicated the building in [[software:onshape:start|]]. This was not as easy as I initially thought, but in the end, I was successful.
-The more interesting part was the electronics. I used an [[hardware:esp32:start|]] as the controller and decided to connect it to the [[..:..:system_control:start|]] with my generic BLE system. Then, I tested if I could replicate the beacon signal (2 seconds on and 2 seconds off). It was the first time I had used hardware timers and interrupts for the LEDs. The beacon's LED will illuminate transparent PLA, making the light visible.
+The more interesting part was the electronics. I used an [[hardware:esp32:h2:start|]] as the controller and decided to connect it to the [[..:..:system_control:start|]] with my [[..:..:system_control:ble:start|]] system. Then, I tested if I could replicate the beacon signal (2 seconds on and 2 seconds off). It was the first time I had used hardware timers and interrupts for the LEDs. The beacon's LED will illuminate transparent PLA, making the light visible.
 A more challenging part will be the outdoor lights, as the building has two of them. I will try to use 0402 3V LEDs and hope that I can print a miniature enclosure to mimic the real lamps.
-==== MCAD ====
+===== KiCad =====
-The modell was created in [[software:onshape:start|]]. More about that later.
+The custom PCBs are created within [[software:kicad:start|]] and manufactured by the sponsor [[https://pcbway.com|PCBWay]].
-==== EDA/ECAD ====
+This is the LED board, with is located a the top within the building. Is has connections to the WS2812B RGB LED and the two outdoor 0402 LEDs, which are within separate housings.
-The two PCBs are created within [[software:kicad:start|]]. The rendering of the main (LED) pcb could be seen here. It's as everything else a work in progress.
 {{:project:maerklin:warnemuende:lighthouse:light_board_front.png?300|}}
 {{:project:maerklin:warnemuende:lighthouse:light_board_back.png?300|}}
-===== Source Code =====
+{{:project:maerklin:warnemuende:lighthouse:light_board.svg?600|}}
+But the LED board can't work without any controller. Here it is.
+{{:project:maerklin:warnemuende:lighthouse:mcu_board_front.png?300|}}
+{{:project:maerklin:warnemuende:lighthouse:mcu_board_back.png?300|}}
+{{:project:maerklin:warnemuende:lighthouse:mcu_board.svg?600|}}
+{{:project:maerklin:warnemuende:lighthouse:mcu_board-buck converter.svg?600|}}
-[[https://github.com/mars3142/warnemuende_lighthouses|Github]] Action: {{https://github.com/mars3142/warnemuende_lighthouses/actions/workflows/esp32_build.yaml/badge.svg?nocache&.png}}